1, The specification as below sheet
| Basic size information |
| Color | White |
| Pitch | 1.00mm |
| Material | PA9T |
| Mating lock | without |
| Wire Termination Method | Crimping |
| Circuits | 8pins/14pins/20pins/30pins |
| Wire Insulation Diameter | 0.60mm Max. |
| Wire range | AWG28# to 32# |
| |
| Electrical properties |
| Current Rating | 1A AC, DC |
| Voltage Rating | 100V AC, DC |
| Contact Resistance | 30mΩ Max |
| Insulation Resistance | 500mΩ min |
| Withstanding Voltage | 500V AC/minute |
| |
| Mechanical properties |
| Temperature range | -25℃ to 85 ℃ |
| Other information please kindly check the following picture. |
2, Related drawing and report
Testing report
| 1. Scope This specification covers the requirements for product performance of 1.00mm pitch wire to board connectors series. 2. Construction,Dimensions,Material & Plating See the attached drawings 3. Ratings & Applicable Wires | Item | Standard | | Rated Voltage (Max.) | 100V AC/DC | Insulation O.D. 0.60mm (Max.) | | Rated Current (Max.) And Applicable Wires | AWG#28 | 1A AC/DC | | AWG#30 | 0.9A AC/DC | | AWG#32 | 0.8A AC/DC | | Ambient Temperature Range | -25℃ ~ +85℃* | *: Including terminal temperature rise 4. Electrical Performance | Test Description | Procedure | Requirement | | 4-1 | Contact Resistance | Mate connectors, measure by dry circuit, 20mV max., 10mA.(Based upon JIS C5402 5.4) | 30mΩ (Max.) | | 4-2 | Insulation Resistance | Mate connectors, apply 200V DC between adjacent terminal or ground. (Based upon JIS C5402 5.2/MIL-STD-202 Method 302 Cond. B) | 500MΩ (Min.) | | 4-3 | Dielectric Withstanding Voltage | Mate connectors, apply 500V AC (rms) for 1 minute between adjacent terminal or ground. (Based upon JIS C5402 5.1/MIL-STD-202 Method 301) | No Breakdown. | | 4-4 | Contact Resistance on Crimped Portion | Crimp the applicable wire on to the terminal, measure by dry circuit, 20mV (Max.)., 10mA. | 5mΩ (Max.) | 5. Mechanical Performance | Test Description | Procedure | Requirement | | 5-1 | Actuator Insertion & Withdrawal Force | Insert and withdraw connectors at the speed rate of 25±3mm / minute. | Refer to paragraph 7 | | 5-2 | Crimping Pull Out Force | Fix the crimped terminal, apply axial pull out force on the wire at the speed rat of 25±3mm / minute.(Based upon JIS C5402 6.8) | AWG#28 | 1.0kgf (Min) | | AWG#30 | 0.8kgf (Min) | | AWG#32 | 0.5kgf (Min) | | 5-3 | Terminal Insertion Force. | Insert the crimped terminal into the housing. | 0.50kgf (Max.) | | 5-4 | Terminal/Housing Retention Force. | Apply axial pull out force at the speed rate of 25±3mm / minute on the terminal assembled in the housing. | 0.50kgf (Min.) | | 5-5 | Pin Retention Force | Apply axial push force at the speed rate of 25±3mm / minute | 0.30kgf (Min.) | | 5-6 | Durability | When mated up to 50 cycles repeatedly by the rate of 10 cycle per minute. | Contact Resistance 60mΩ (Max.) | | 5-7 | Vibration | Amplitude: 1.5mm P-P Sweep time: 10-55-10 Hz in 1 minute Duration: 2 hours in each X.Y.Z. axes. (Based upon MIL-STD-202 Method 201A) | Appearance No Damage. Contact Resistance 60mΩ (Max.) Discontinuity 1 μsec.(Max.) | | 5-8 | Physical Shock | 490m/s²｛50G｝,3 strokes in each X.Y.Z. axes. (Based upon JIS C0041/MIL-STD-202 Method 213B Cond. A) | |
| 6. Environmental Performance And Others | Test Description | Procedure | Requirement | | 6-1 | Temperature Rise | Carrying rated current load.(Based upon UL 498) | 30℃(Max.) | | 6-2 | Heat Resistance | 85±2℃,96 hours (Based upon JIS C0021/MIL-STD-202 Method 108A Cond. A) | Appearance No Damage. Contact Resistance 60mΩ (Max.) | | 6-3 | Cold Resistance | -25±3℃,96 hours (Based upon JIS C0020) | | 6-4 | Humidity | Temperature: 40±2℃ Relative Humidity : 90~95% Duration: 96 hours (Based upon JIS C0022/MIL-STD-202 Method 103B Cond. B) | Appearance No Damage. Contact Resistance 60mΩ (Max.) Insulation Resistance 10MΩ (Min.) Dielectric Withstanding Voltage Must meet 4-3 | | 6-5 | Temperature Cycling | 5 cycles of: a) -55℃ 30 minutes b) +85℃ 30 minutes (Based upon JIS C0025) | Appearance No Damage. Contact Resistance 60mΩ (Max.) | | 6-6 | Salt Spray | Tin-plated 12 hours / Gold- plated 24 hours exposure to a salt spray from the 5±1% solution at 35±2℃. (Based upon JIS C0023/MIL-STD-202 Method 101C Cond. B) | | 6-7 | SO2 Gas | 24 hours exposure to 50±5ppm. SO2 gas at 40±2℃. | | 6-8 | NH3 Gas | 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. | | 6-9 | Solderability | Soldering Time: 5±0.5 sec. Solder Temperature: 245±5℃ | Solder Wetting 95% of immersed area must show no voids, pin holes | | 6-10 | Resistance to Soldering Heat | When reflowing Refer to paragraph 8 Solder iron method Soldering Time: 5±0.5 sec. Solder Temperature: 370℃ ~ 400℃ | Appearance No Damage. | 7. Actuator Insertion/Withdrawal Force [Unit : kgf] | Circuits | At Initial | | Insertion (Max.) | Withdrawal (Min.) | | 08 | 1.6 | 0.20 | | 14 | 2.8 | 0.35 | | 20 | 4.0 | 0.50 | | 30 | 6.0 | 0.75 | |
3, FAQ about our company
1, Q: Do you have a catalogue? Can you send me the catalogue to have a check of all your products?
A: Yes, We have product catalogue. Please contact us on line or send an Email to send the catalogue.
2, Q: Do you have a price list? I need your price list of all your products.
A: We do not have a price list of all of our products. Because we have so many items, and it's impossible to mark all of their price on a list. And the price are always changing because of the producing cost. If you want to check any price of our products, please feel free to contact us. We will send offer to you soon!
3, Q: I can’t find the product on your catalogue, Can you make this product for me?
A: Our catalogue shows most of our products, but not all. So just let us know what product do you need, and how many do you want. If we do not have it, we can also design and make a new mould to produce it. For your reference, making a ordinary mould will take about 20-35 days.
4, Our Services
Customizable specification drawing and material is avaiable.More than 12 years experience in conenctor, wire housing, wafer, terminals, other metal parts, etc. Products samples is free, you just need pay for the freight. Besides, we have a strict quality control systerm, so we are accepted by famouse and international company like TPV, LeTV, Emerson, Amphenol Corporation, Skyworth,BYD, LuXshare,etc.
Product Tags:
|
|
nicked-plated shell 0.039 inch pitch PA66 material crimp type DF19 wire to board connector Images
|
